Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing changed? Glance into the tank, and you may see no water inside. Before you stress, rest assured that fixing this issue is usually simple. If you can’t do it yourself, you can always set up toilet repair with a knowledgeable plumber. Follow these recommendations to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first step is to ensure that the water is turned on. If you or someone in your household recently performed a toilet repair, you probably turned off the water first. Did you forget to turn it back on? To find out, rotate the water shut-off valve on the wall in back of the toilet. If the valve was shut, water ought to now start refilling the tank. If this does not work, test the water at your sink or another plumbing fixture. If nothing comes out from the tap, you might have a larger water supply issue. Contact your water company to learn more. 

Reposition or Replace the Float Mechanism 

Older toilet designs use a float ball to measure the water level as it increases in the tank. When the ball reaches a specified height, the float arm it’s joined to stops the water flow. However, insufficient water could enter the tank if the ball is positioned incorrectly or the arm is broken. To move the float ball, start by removing the toilet tank lid. Bend the float arm up a little to adjust where it sits in the tank. If this fails to fix the problem, you may need to replace the full float mechanism. You should be able to perform this yourself by following the instructions that come with the replacement parts, or you can hire a plumber for help. Just realize that float balls are old toilet systems. You may appreciate improved durability and efficiency if you upgrade the existing tank components or replace the toilet completely. 

Adjust the Fill Valve 

More recent toilets operate with a float cup rather than a float ball, coupled with a fill valve and water level rod. There could quite possibly be no water in the toilet tank because the valve has slipped out of place or become plugged. Here are recommendations to consider: 

• Test the fill valve: Glance inside the toilet and identify the fill valve on top of a vertical tube device on the left side of the tank. Ensure it’s secure and evenly ahered to the tube. Then, fine-tune the water level. Newer toilets have an adjustment knob you can turn manually, while older versions may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and make it possible for the tank refill to verify the water level. Modify it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other gunk might be covering the valve and preventing your toilet from filling. Shut down the water behind the toilet and remove the fill cap. Then, steadily turn the water back on, cupping your hand over the valve to prevent water from spraying everywhere. After several seconds, turn the water back off. Finally, scrub the fill cap to clear away hard water buildup. If the cap is broken, swap it out. 
• Clean the valve tube: The tube below the fill valve might also be blocked. Shut off the water and take away the valve hardware. Then, insert a slim bottle brush or wire down the tube. Turn the water back on just a little to flush away the blockage. Replace the valve hardware and flush the toilet to test your adjustments. 

Repair or Replace the Trip Assembly 

If you’ve attempted the steps above without success, the final possibility is a faulty trip assembly. This component links the flush handle to the tank. If it’s damaged or positioned improperly, the flush cycle may not complete, leaving the tank void. Remove the toilet tank lid and look at the trip assembly fastened to the handle. If it’s out of place, reposition it. If the assembly is bent, worn or busted, replace it. Whether you perform the job yourself or leave it to a plumber, this uncomplicated repair should get your toilet tank filled with water once more. 

Schedule Toilet Repair Today 

You can’t go long without a functional toilet, so reach out to [Company name] to request a toilet repair. We can diagnose why your toilet isn’t filling and propose the correct fix. If your plumbing fixture is outdated and worn out, our team will install a high-efficiency toilet in your home. Be assured that every plumbing repair and replacement we complete is backed by a 100% satisfaction guarantee. To schedule an evaluation from one of our licensed team members, please call your local Service Experts Heating, Air Conditioning & Plumbing office today.